010203
ADL100-EY Single-phase Prepaid&Postpaid Energy Meter
ADL100 single-phase prepaid watt-hour meter and ADL300 three-phase prepaid watt-hour meter are new prepaid watt-hour meters that integrate measurement and control. Support RF recharge and remote recharge, with prepaid control, time control, malignant load control and other control modes. It can be built in 100A large capacity magnetic holding relay to realize partial closing of the meter, and can also provide passive dry contact output control external circuit breaker to realize tripping function. It is widely used in the pre-paid electricity management of commercial square, resident dormitory and college dormitory.
FEATURES
Local&Online Topping Up
● Topping up by RFID Card (Local)
● Topping up by Mobile APP (Online)
● Topping up by Prepaid System (Online)
● Low Balance Credit Alarm by sending SMS
Multi Circuits Metering for 1-phase&3-phase
● 3 Types of Multi-circuits Combination
● Max 36 Circuits 1-phase Metering
● Max 12 Circuits 3-phase Metering
● Mixed (1-phase&3-phase Circuits Metering)
Auto&Remote Switch Control
● Meter Supports Prepaid Mode & Postpaid Mode
● Auto Tripping when Balance Credit is below Zero (Prepaid Mode)
● Before Auto Tripping, Power Users can receive Low Balance Alarm by SMS
● Remote Swtich Control by using Prepaid System (Prepaid&Postpaid Mode)
● Prepaid&Postpaid Mode of Meters can be set using Prepaid System
Multi-rate&Multi-tariff
● 4 Tariff Rates (Spike, Peak, Flat, Valley kWh Unit Price)
● 14 Time Intervals by Day
● Set Unit Price of Electricity Consumption for different Time Period of 1 Day
PIN OVERVIEW
WIRING
Direction Connect (1-phase&3-phase)
Connect via CTs (3-phase)
APPLICAITON
APPLICAITON SCENARIOS
ONE-STEP DIRECT SOLUTION
LORA-BASED INDIRECT SOLUTION
WIRING DIAGRAM
WIRING DIAGRAM
Step ①: Correctly install&wire meters
1. 35mm DIN-rail installation
2. 3-phase 4-wire or 3-phase 3-wire methods
3. Voltage signal input via direct connect or PTs
4. Current signal input via CTs or Rogowski Coils
5. Power supplied by 85~265Vac L-N power source
Step ②: Download&Register IoT APP
1. Introduction of IoT Energy Monitoring Solution (IoT EMS)
2. Introduction of IoT EMS APP (for mobile users)
3. Introduction of IoT EMS WEB (for PC users)
4. Download of IoT EMS APP
5. Register your account with 3-month Free Trial
6. Or contact us to get Test Account
Step ③: Add Meters to your Account
1. Meters are recognized by unique SN code
2. Scan QR code to add meter to your account
3. Edit CT&PT ratio according to paired CT&PT
4. If voltage input via direct connect, PT ratio set to 1 (Actual Power System Voltage = Voltage Signal Input of Meter)
5. If current input via 250A/5A CTs for example, CT ratio set to 50 (250÷5=50)
Step ④: Start your 3-month Free Trial
1. After 3 months, host service&buy-out service will be available for account renewal
2. Contact us for more information about system charge item&meter quotation
3. Before we send you the quotation, we will set a solution acoording to your request
4. Provide full technical support for installing meters and connecting meters to our system
[Certificate 2023.08.18] CE Certificate ADL100-EY Series
[Datasheet 2023.08.18] ADL100-EY 1-phase Prepaid&Postpaid Energy Meter Datasheet
[Instruction 2023.08.18] ADL100-EY & ADL300-EY Common FAQ & Trouble Shooting